JAFU / Equipment
M80S

Earlier catalogue reference retained at its original URL. The current 20261117 JAFU catalogue is a separate source version; no hardware equivalence is asserted.
M80S is a remote-controlled vertical-blade mower.
Describe the maintenance task
Include the area, vegetation, target finish, mowing schedule, access route and working conditions, together with moving and storage constraints.
Configuration and operation
Confirm the configuration for your model and version: blade and cutting-height arrangement, drive, engine and electrical configuration, dimensions and weight. Review the operating limits and the documents needed to assess the task.
Parts and documentation
For parts, identify the machine, component and component position. Confirm the operating, maintenance and parts information applicable to the exact model version.
Can the same part be used across M80S versions?
Provide the machine and part identification and request version-specific confirmation. A shared model name or similar appearance does not establish compatibility.
M80S is identified as a remote-controlled vertical-blade mower in the supplied JAFU model material. Begin with the maintenance task and the proposed version rather than assuming that a model name establishes dimensions, cutting performance or part compatibility.
Describe the maintenance requirement
State the area, vegetation and target finish. Include the mowing schedule you want to assess, access route, working surface and obstacles. Record constraints on moving, transporting and storing the machine. These details help define the questions for a configuration discussion without turning an unverified catalogue claim into a promise.
Keep the comparison on a common basis
Use the proposed M80S configuration when comparing the blade and cutting-height arrangement, drive, engine and electrical system, dimensions and weight. Record the document version beside each value. A blank field remains a question; it should not be completed with a figure taken from M-50S, M80S-D or a newer unnamed mower family.
The present evidence supports the model/category association and catalogue image provenance. It does not establish current numeric specifications, a working-slope limit, output, runtime or a performance advantage over another model.
Confirm operation and support information
Review the applicable instructions, operating limits and supervision requirements for the intended task. Keep machine-label details and the component reference for parts discussions. Ask which model-specific documents are available rather than treating a product catalogue as an operating or repair manual.
Questions before selection
Is M80S necessarily better than M-50S for a larger site?
The current verified information does not establish that comparison. Compare confirmed configurations and the actual maintenance requirement; do not infer output or suitability from the model number.
What if the site has restricted access or gradients?
Include the usable access and ground conditions in the brief, and review the exact configuration and operating limits. This introduction does not approve operation at a particular site.
Discuss the M80S requirement
Open the existing model enquiry link with the task, version if known and documentation questions ready. Support and mowing-category information remain available through the existing routes. The private preview contact form is a local test, with external sending disabled.
How to Compare Agricultural Mowing Machines · Application scenarios
Catalogue specifications and configuration reference
Source: JAFU mowing equipment catalogue v11 (Chinese), physical page 11, M80S. The entries below describe the model sheet. Confirm the exact version and configuration offered in a quotation. Nominal entries are not independent test results, operating instructions or performance guarantees.
Power and transmission
- Engine description: a 192-series single-cylinder air-cooled diesel engine. The source also prints the domestic label 国二; that label does not establish compliance for an overseas destination, and 192 is not stated as 192 cc.
- Travel motors: two 800 W brushless motors. This is not an engine-power or cutting-output figure.
- Generator entry: 2000 W, described as internally excited. This is a catalogue rating, without an independent electrical test.
- Nominal horsepower entry: 13 HP. No conversion or field-productivity result is inferred.
- Power-system description: fuel-electric hybrid. The description does not establish pure-electric operation or autonomy.
- Gearbox description: differential gearbox. A specific gearbox SKU or operating sequence is not supplied.
- Battery entry: 24 V 20 Ah. The page does not specify battery quantity, chemistry, charging procedure or endurance.
Cutting arrangement
- Cutting width: 80 cm on the exact M80S v11 model sheet. No value is transferred from M80F, JF80 or a generic mower-family table.
- Tool-height adjustment entry: 2–20 cm. This is not a universal achievable grass height or a setup instruction.
- Blade entry: 6 mm manganese-steel serrated blades. The entry does not establish hardness, service life or replacement compatibility.
Dimensions and packing
- Nominal machine-size entry: 160 × 90 × 89.5 cm. Confirm the offered configuration and its complete handling envelope separately.
- Nominal machine-mass entry: 378 kg. The page does not qualify this as dry, wet or gross shipping mass.
- Wooden-crate size entry: 160 × 110 × 103 cm. Identify the packing proposed for the actual order.
- Wooden-crate mass entry: 51 kg. It is not an asserted gross shipping weight.
- Three-machine rack size entry: 160 × 104 × 225 cm. The label specifically refers to a rack for three machines, not a stacking-safety or delivery promise.
Points to confirm for the offered version
The track-size row has no printed unit or defined axes, so it cannot be used as a clearance dimension. Confirm the quoted version and the conditions for speed and radio range. The catalogue entries do not establish throughput, endurance or safe operating limits.
Prepare a M80S purchasing record
Keep the task requirements and the proposed M80S version in the same record. Use your own site information for the requirement column, and an attributable model-specific document for every machine value. This keeps a requested result separate from a confirmed configuration.
Task requirement
- Information to prepare: Vegetation, desired finish and target cutting height
- How to use it: A target is a buyer requirement. Confirm the proposed cutting arrangement separately.
Access and handling
- Information to prepare: Narrowest access, turns, obstacles, transport and storage route
- How to use it: Compare attributable dimensions and mass for the proposed version.
Ground and operating context
- Information to prepare: Surface, gradients and intended mowing schedule
- How to use it: Use the applicable instructions and operating limits; a photograph is not a slope rating.
Configuration reference
- Information to prepare: Exact model, version and quotation reference
- How to use it: Keep the cutting, drive, engine/electrical and control information tied to that reference.
Documents and parts
- Information to prepare: Document title/revision and any machine/component identification
- How to use it: A catalogue introduces a model. Confirm which instructions or parts record applies.
Keep unresolved configuration fields as questions in the enquiry. Retain the source title, page or revision beside each reply so that a later quotation can be checked against the same requirement.