JAFU / Equipment
M-50S

Earlier catalogue reference retained at its original URL. The current 20261117 JAFU catalogue is a separate source version; no hardware equivalence is asserted.
M-50S is a remote-controlled vertical-blade mower.
Describe the mowing task
Include the vegetation, desired cutting height, ground surface and gradients, narrowest access, obstacles, and transport or storage constraints.
Configuration and operation
Confirm the configuration for your model and version: cutting width and height range, blade arrangement, drive and engine, dimensions and weight. Review the controls, required supervision and operating limits against the intended task.
Parts and documentation
For parts, identify the machine, component and component position. Confirm the operating, maintenance and parts information applicable to the exact model version.
Does M-50S specify the cutting width?
Use M-50S as the model reference and request the specification for the proposed version. Do not use the model name in place of a confirmed configuration sheet.
M-50S is a remote-controlled vertical-blade mower identified in the supplied JAFU catalogue. Use the model reference to begin a mowing discussion, then confirm the proposed version against the actual task. The model name is not a cutting-width specification or a statement of operating suitability.
Build the mowing brief
Describe the vegetation, desired cutting height and finish, working area and mowing frequency. Add the ground surface, gradients, obstacles and narrowest access. Transport and storage constraints belong in the same brief: a machine that can reach the work area still needs a suitable route and space for handling.
Compare a specified configuration
Keep the proposed version beside the quotation and applicable documents. Compare the cutting arrangement and height range, drive and engine configuration, overall dimensions and weight using information confirmed for that version. Do not fill missing values from another mower, a similar photograph or a different catalogue edition.
The available source identifies the model and category. A current configuration sheet, operating limits and supporting test information still need confirmation. No cutting width, slope rating, work rate, runtime or unattended capability is promised in this model introduction.
Operation, documentation and parts
Review the controls, required supervision and operating limits before equipment selection. For parts, identify the machine, component and component position. A photograph can help communicate the request, but matching appearance alone does not establish compatibility. Confirm which operating, maintenance and parts documents apply to the proposed version.
Questions before an enquiry
Can a slope in a catalogue image establish an operating limit?
No. The relevant configuration, instructions and actual ground conditions must be assessed. A picture is not a verified safe-slope rating.
What should a parts request include?
Include the machine identity, version if known, part identification and location, and the issue being discussed. Confirm compatibility before ordering.
Discuss M-50S
Prepare the task brief and model reference for the existing contact page. You can also review the mowing category or support information. The current private preview uses a local test form; it does not send an external enquiry.
How to Compare Agricultural Mowing Machines · Application scenarios
Related reading: Buyer Guides
Catalogue specifications and configuration reference
Source: JAFU mowing equipment catalogue v11 (Chinese), physical page 8, M-50S. The entries below describe the model sheet. Confirm the exact version and configuration offered in a quotation. Nominal entries are not independent test results, operating instructions or performance guarantees.
Electrical and transmission
- Generating-power entry: 1.5 kW. This is the listed generator value, not engine output.
- Transmission: belt transmission. The entry does not describe a detailed power path or maintenance procedure.
- Control voltage: 24 V. Battery quantity, chemistry and charging procedure are not specified by this entry.
- Travel motors: two 580 W brushless motors, as printed on this M-50S page.
Configuration entries
- Engine entry: 凯立发178 with electric start. The page does not assign that engine entry separately to both named fuel variants; the printed 178 reference is not a stated displacement.
- Fuel-tank entries: diesel version 4 L; petrol version 2.6 L. Keep each value with its named fuel variant when reviewing a quotation.
- Machine-mass entries: diesel version 202 kg; petrol version 192 kg. These are separate model-sheet entries, without a loaded-machine or gross-shipment qualification.
Cutting arrangement
- Cutting width: 50 cm, listed for M-50S on this catalogue page. This value comes from the model sheet, not the model name.
- Retained-grass-height entry: 0–12 cm. This nominal catalogue range is not a setup instruction or a guaranteed field finish.
- Blade entry: 36 vertical flail blades. The count does not establish blade interchangeability with another model.
- Lifting method: manual lifting. Electric or automatic height adjustment is not established by this entry.
- Clutch-control entry: throttle control. The entry does not identify a centrifugal-clutch design or an operating sequence.
Packing reference
- Wooden-crate size entry: 115 × 113 × 87 cm. This is a catalogue packing reference, not a loading plan or confirmation of the packing for a current order.
- Wooden-crate mass entry: 30 kg. This is the crate mass, not the total consignment mass.
Points to confirm for the offered version
The printed track-width and machine-width entries need reconciliation before confirmed overall dimensions or access clearance can be given. Clarify the speed entry and its conditions, and confirm the engine/fuel variant, operating limits and applicable instructions. The catalogue does not establish work rate, runtime or unattended operation.
Prepare a M-50S purchasing record
Keep the task requirements and the proposed M-50S version in the same record. Use your own site information for the requirement column, and an attributable model-specific document for every machine value. This keeps a requested result separate from a confirmed configuration.
Task requirement
- Information to prepare: Vegetation, desired finish and target cutting height
- How to use it: A target is a buyer requirement. Confirm the proposed cutting arrangement separately.
Access and handling
- Information to prepare: Narrowest access, turns, obstacles, transport and storage route
- How to use it: Compare attributable dimensions and mass for the proposed version.
Ground and operating context
- Information to prepare: Surface, gradients and intended mowing schedule
- How to use it: Use the applicable instructions and operating limits; a photograph is not a slope rating.
Configuration reference
- Information to prepare: Exact model, version and quotation reference
- How to use it: Keep the cutting, drive, engine/electrical and control information tied to that reference.
Documents and parts
- Information to prepare: Document title/revision and any machine/component identification
- How to use it: A catalogue introduces a model. Confirm which instructions or parts record applies.
Keep unresolved configuration fields as questions in the enquiry. Retain the source title, page or revision beside each reply so that a later quotation can be checked against the same requirement.